what are you looking for?
Item NO.:
TPK-30AProduct Origin:
Quanzhou, Fujian, ChinaColor:
Orange and dark grayProduct weight:
85 kgShipping Port:
To be confirmed in quotationLead Time:
Depends on configuration
The HUADA TPK-30A provides a fixed-frequency refrigerated dryer for a larger workshop air flow. Designed for production cells, assembly workshops and grouped pneumatic equipment, it removes moisture from compressed air by cooling the air, separating condensed water and discharging the condensate automatically.
This fixed-frequency model has a nominal air treatment capacity of 3.8 m³/min and uses R410A refrigerant. The pressure-dew-point range is 2–10°C, subject to operating conditions. The package measures 600 × 560 × 850 mm, weighs 85 kg and connects through G1 1/2 air ports.
1. 3.8 m³/min nominal air-treatment capacity
The TPK-30A is sized for a nominal treatment capacity of 3.8 m³/min. Match the dryer to the actual compressed-air flow, working pressure, inlet temperature and ambient conditions when planning production cells, assembly workshops and grouped pneumatic equipment.
2. Fixed-frequency design with 1.125 kW total unit power
The TPK-30A uses a fixed-frequency configuration with a listed total unit power of 1.125 kW and a 220 V / 50 Hz supply. Its refrigeration, heat-exchange and control systems form a compact, integrated drying package.
3. Air-to-air heat recovery and outlet reheat
Incoming warm compressed air exchanges heat with the outgoing cold, dry air before entering the evaporator. This precools the inlet air and recovers cooling energy. The outgoing dry air is reheated before leaving the dryer.
4. Refrigerated moisture condensation and separation
The refrigeration stage cools compressed air so that water vapor condenses. The separator removes the resulting liquid from the air stream. The 2–10°C pressure-dew-point range is dependent on operating conditions and should be checked against the process requirement.
5. Automatic condensate drainage
Separated water is discharged through an automatic drain, reducing the need for manual emptying. Keep the drain accessible and provide a suitable condensate discharge route so that collected water can leave the dryer.
6. Microcomputer control and integrated system layout
Temperature sensors work with the microcomputer control system to monitor operation and support protective functions. The heat-exchange, refrigeration and electrical-control sections are integrated in one cabinet for an orderly installation and routine servicing.
7. Defined connection and cabinet size
The TPK-30A uses G1 1/2 air connections, measures 600 × 560 × 850 mm and weighs 85 kg. These values support pipework, handling and service-access planning. The supplied product appearance combines orange panels with a dark gray cabinet.
HUADA TPK-30A · 3.8 m³/min nominal treatment capacity · Fixed-frequency refrigerated air dryer
| Parameter | TPK-30A |
|---|---|
| Performance and control | |
| Model | TPK-30A |
| Dryer type | Refrigerated compressed air dryer |
| Control type | Fixed-frequency |
| Nominal air treatment capacity | 3.8 m³/min |
| Pressure dew point | 2–10°C (subject to operating conditions) |
| Power supply and refrigeration | |
| Power supply | 220 V / 50 Hz |
| Total unit power | 1.125 kW |
| Refrigerant | R410A |
| Connections and dimensions | |
| Air inlet/outlet connection | G1 1/2 |
| Overall dimensions | 600 × 560 × 850 mm |
| Unit weight | 85 kg |
| Product origin | Quanzhou, Fujian, China |
Air treatment capacity is a nominal model value. Select the dryer for the actual inlet temperature, ambient temperature, working pressure, air flow and required pressure dew point. The stated 2–10°C range is subject to operating conditions. Dimensions follow the listed sequence; confirm connection and installation details in the quotation.
Air flow and drying duty: Check the actual flow against the 3.8 m³/min nominal capacity. State the working pressure, inlet and ambient temperatures, and required pressure dew point so that the dryer can be selected for the intended duty.
Electrical supply: The specified supply is 220 V / 50 Hz. The listed total unit power is 1.125 kW. Confirm phase, protection and connection details for the installation.
Pipework and condensate: Plan the connection to the G1 1/2 inlet/outlet ports, allow access to the condensate drain and provide a suitable discharge route. Specify any upstream or downstream filtration required for the process.
Position and maintenance: Allow for the 600 × 560 × 850 mm overall dimensions and 85 kg unit weight. Keep cabinet ventilation openings clear and provide access to controls, drain components and service panels.
| Before you order | What to confirm |
|---|---|
|
Quotation requirements |
Please provide your required operating pressure, average and peak air demand, power supply, order quantity and destination. |
|
Equipment scope |
The quotation specifies the selected equipment configuration and any receiver, dryer, filters or accessories included. |
|
Delivery and shipment |
Production lead time and shipping arrangements are quoted according to the selected configuration, quantity and destination. |
|
Technical documentation |
Please identify any documentation or destination-specific requirements needed for your purchasing process so that we can assess them for the selected configuration. |
|
Warranty and after-sales support |
Warranty coverage, service arrangements and spare-parts support are defined in the agreed quotation and order documents. |
Explore HUADA’s manufacturing facilities and request the technical documentation relevant to your selected configuration and destination.
View our factory
Review qualification documents
Is the TPK-30A power rating 1.125 kW?
Yes. The listed total unit power of the TPK-30A is 1.125 kW. Its nominal treatment capacity is 3.8 m³/min, its supply is 220 V / 50 Hz and its air connection is G1 1/2. The unit measures 600 × 560 × 850 mm and weighs 85 kg.
Can I select this dryer using compressor motor power alone?
Use the actual compressed-air flow and operating conditions. The TPK-30A has a nominal treatment capacity of 3.8 m³/min, while the required selection also depends on working pressure, inlet temperature, ambient temperature and the target pressure dew point. Compressor motor power alone does not define the dryer duty.
Does a 2–10°C pressure dew point describe the outlet air temperature?
Pressure dew point describes the moisture condition of compressed air at operating pressure. It is different from the outlet air temperature. In this dryer, the outgoing dry air passes back through the air-to-air heat exchanger and is reheated before discharge. Verify the required dew point for the actual operating conditions.
Does refrigerated drying also define the complete air-purity grade?
This dryer removes moisture by refrigeration, liquid separation and automatic drainage. Select additional filtration and any further treatment according to the process requirements. A specified dew point by itself does not establish the complete particle, oil or application-specific air-purity requirement.
07 Request a Quotation for TPK-30A
Request a quotation for the HUADA TPK-30A. Send the actual compressed-air flow, working pressure, inlet temperature, ambient temperature and required pressure dew point so that we can review the selected 3.8 m³/min nominal dryer configuration.
Include the site power supply, connection requirements, required filtration, operating hours, order quantity and destination. We will confirm the equipment configuration, installation information and commercial terms for your air-treatment system.
Leave A Message
Refrigerated Air Dryer For Air Compressor
The refrigeration dryer is composed of drying chamber,vacuum system,heat source,and low temperature condenser.In stric accordance with iso9001,gb150,iso7183 refrigerant air dryer standard,qs,pressure vessel inspection specifications for design and manufacture of production and testing,to ensure product safety and reliable operation.
HUADA TPK-10A 1.6 m³/min Fixed-frequency Refrigerated Air Dryer
The HUADA TPK-10A is a fixed-frequency refrigerated compressed air dryer with a nominal treatment capacity of 1.6 m³/min. It combines air-to-air heat recovery, refrigerated moisture condensation and automatic condensate drainage in an orange and dark gray cabinet. Supply: 220 V / 50 Hz; air connection: G1.
HUADA TPK-20A 2.6 m³/min Fixed-frequency Refrigerated Air Dryer
The HUADA TPK-20A is a fixed-frequency refrigerated compressed air dryer with a nominal treatment capacity of 2.6 m³/min. It combines air-to-air heat recovery, refrigerated moisture condensation and automatic condensate drainage in an orange and dark gray cabinet. Supply: 220 V / 50 Hz; air connection: G1.
4KW SE series mobile screw air compressor
SE series permanent magnet variable frequency screw air compressor is a product with great design creativity. Compared with the same power machine, its volume is optimized by 40%, which refreshes the taste with compact design and inherits the ingenuity with quality technology. The materials are full of power, showing quality and exquisiteness everywhere, and every detail perfectly presents color, design and materials.
HB-20TD Medium-Pressure Permanent Magnet Variable Frequency Drive Unit (15 kW, dedicated for laser cutting applications)
The HB-20TD is the flagship model in Huada's medium-pressure integrated system series, featuring a 15 kW permanent magnet frequency converter with a discharge capacity of 1.5 m³/min and stable pressure of 1.6 MPa, specifically designed for 1500–3000 W fiber laser cutting machines. Its integrated solution simplifies traditional multi-unit series configurations into a single unit, offering compact size, short piping requirements, and low pressure loss.
10hp 7.5kw All In One Screw Air Compressor With 180L Air Tank
This series of all in one screw air compressor is designed and manufactured by our company for small and medium-sized enterprises.It is cost-effective and provides reliable and efficient compressed air solutions for small and medium-sized enterprises.
HUADA SED-150+ 110 kW Air-Cooled Two-Stage Permanent Magnet VSD Screw Air Compressor
The HUADA SED-150+ is an air-cooled SED+ series screw air compressor delivering 23.5 m³/min at 0.8 MPa from a 110 kW motor. An IE5 permanent magnet motor, dual VFD control and a DN80 outlet provide a defined package for a high-volume industrial air station.
LG-30G 22 kW Direct Drive Screw Air Compressor
The LG-30G is an air-cooled direct drive screw air compressor with a 22 kW motor, for workshops and production areas with steady compressed-air demand. Air delivery for the fixed-speed configuration is 3.8 m³/min at 8 bar and 3.2 m³/min at 10 bar, with separate specifications at 7 and 12 bar. Its 1320 × 800 × 1300 mm cabinet has a smaller footprint than the LG-50G. Direct drive, inlet filtration and oil-air separation support workshop air supply.
IPv6 network supported
English
français
Deutsch
русский
español
português
日本語
한국의
ไทย
中文
