what are you looking for?
Item NO.:
TPK-10AProduct Origin:
Quanzhou, Fujian, ChinaColor:
Orange and dark grayProduct weight:
70 kgShipping Port:
To be confirmed in quotationLead Time:
Depends on configuration
The HUADA TPK-10A provides a compact refrigerated drying stage for a local compressed-air supply. Designed for individual pneumatic workstations and small workshop air networks, it removes moisture from compressed air by cooling the air, separating condensed water and discharging the condensate automatically.
This fixed-frequency model has a nominal air treatment capacity of 1.6 m³/min and uses R410A refrigerant. The pressure-dew-point range is 2–10°C, subject to operating conditions. The package measures 500 × 450 × 700 mm, weighs 70 kg and connects through G1 air ports.
1. 1.6 m³/min nominal air-treatment capacity
The TPK-10A is sized for a nominal treatment capacity of 1.6 m³/min. Match the dryer to the actual compressed-air flow, working pressure, inlet temperature and ambient conditions when planning individual pneumatic workstations and small workshop air networks.
2. Fixed-frequency design with 0.65 kW total unit power
The TPK-10A uses a fixed-frequency configuration with a listed total unit power of 0.65 kW and a 220 V / 50 Hz supply. Its refrigeration, heat-exchange and control systems form a compact, integrated drying package.
3. Air-to-air heat recovery and outlet reheat
Incoming warm compressed air exchanges heat with the outgoing cold, dry air before entering the evaporator. This precools the inlet air and recovers cooling energy. The outgoing dry air is reheated before leaving the dryer.
4. Refrigerated moisture condensation and separation
The refrigeration stage cools compressed air so that water vapor condenses. The separator removes the resulting liquid from the air stream. The 2–10°C pressure-dew-point range is dependent on operating conditions and should be checked against the process requirement.
5. Automatic condensate drainage
Separated water is discharged through an automatic drain, reducing the need for manual emptying. Keep the drain accessible and provide a suitable condensate discharge route so that collected water can leave the dryer.
6. Microcomputer control and integrated system layout
Temperature sensors work with the microcomputer control system to monitor operation and support protective functions. The heat-exchange, refrigeration and electrical-control sections are integrated in one cabinet for an orderly installation and routine servicing.
7. Defined connection and cabinet size
The TPK-10A uses G1 air connections, measures 500 × 450 × 700 mm and weighs 70 kg. These values support pipework, handling and service-access planning. The supplied product appearance combines orange panels with a dark gray cabinet.
HUADA TPK-10A · 1.6 m³/min nominal treatment capacity · Fixed-frequency refrigerated air dryer
| Parameter | TPK-10A |
|---|---|
| Performance and control | |
| Model | TPK-10A |
| Dryer type | Refrigerated compressed air dryer |
| Control type | Fixed-frequency |
| Nominal air treatment capacity | 1.6 m³/min |
| Pressure dew point | 2–10°C (subject to operating conditions) |
| Power supply and refrigeration | |
| Power supply | 220 V / 50 Hz |
| Total unit power | 0.65 kW |
| Refrigerant | R410A |
| Connections and dimensions | |
| Air inlet/outlet connection | G1 |
| Overall dimensions | 500 × 450 × 700 mm |
| Unit weight | 70 kg |
| Product origin | Quanzhou, Fujian, China |
Air treatment capacity is a nominal model value. Select the dryer for the actual inlet temperature, ambient temperature, working pressure, air flow and required pressure dew point. The stated 2–10°C range is subject to operating conditions. Dimensions follow the listed sequence; confirm connection and installation details in the quotation.
Air flow and drying duty: Check the actual flow against the 1.6 m³/min nominal capacity. State the working pressure, inlet and ambient temperatures, and required pressure dew point so that the dryer can be selected for the intended duty.
Electrical supply: The specified supply is 220 V / 50 Hz. The listed total unit power is 0.65 kW. Confirm phase, protection and connection details for the installation.
Pipework and condensate: Plan the connection to the G1 inlet/outlet ports, allow access to the condensate drain and provide a suitable discharge route. Specify any upstream or downstream filtration required for the process.
Position and maintenance: Allow for the 500 × 450 × 700 mm overall dimensions and 70 kg unit weight. Keep cabinet ventilation openings clear and provide access to controls, drain components and service panels.
| Before you order | What to confirm |
|---|---|
|
Quotation requirements |
Please provide your required operating pressure, average and peak air demand, power supply, order quantity and destination. |
|
Equipment scope |
The quotation specifies the selected equipment configuration and any receiver, dryer, filters or accessories included. |
|
Delivery and shipment |
Production lead time and shipping arrangements are quoted according to the selected configuration, quantity and destination. |
|
Technical documentation |
Please identify any documentation or destination-specific requirements needed for your purchasing process so that we can assess them for the selected configuration. |
|
Warranty and after-sales support |
Warranty coverage, service arrangements and spare-parts support are defined in the agreed quotation and order documents. |
Explore HUADA’s manufacturing facilities and request the technical documentation relevant to your selected configuration and destination.
View our factory
Review qualification documents
What duty does the TPK-10A cover?
The TPK-10A has a nominal air treatment capacity of 1.6 m³/min, a listed total unit power of 0.65 kW and a 220 V / 50 Hz supply. It is suitable for a local air-treatment layout where the actual flow and inlet conditions match the selected duty. Its air connection is G1.
Can I select this dryer using compressor motor power alone?
Use the actual compressed-air flow and operating conditions. The TPK-10A has a nominal treatment capacity of 1.6 m³/min, while the required selection also depends on working pressure, inlet temperature, ambient temperature and the target pressure dew point. Compressor motor power alone does not define the dryer duty.
Does a 2–10°C pressure dew point describe the outlet air temperature?
Pressure dew point describes the moisture condition of compressed air at operating pressure. It is different from the outlet air temperature. In this dryer, the outgoing dry air passes back through the air-to-air heat exchanger and is reheated before discharge. Verify the required dew point for the actual operating conditions.
Does refrigerated drying also define the complete air-purity grade?
This dryer removes moisture by refrigeration, liquid separation and automatic drainage. Select additional filtration and any further treatment according to the process requirements. A specified dew point by itself does not establish the complete particle, oil or application-specific air-purity requirement.
07 Request a Quotation for TPK-10A
Request a quotation for the HUADA TPK-10A. Send the actual compressed-air flow, working pressure, inlet temperature, ambient temperature and required pressure dew point so that we can review the selected 1.6 m³/min nominal dryer configuration.
Include the site power supply, connection requirements, required filtration, operating hours, order quantity and destination. We will confirm the equipment configuration, installation information and commercial terms for your air-treatment system.
Leave A Message
Refrigerated Air Dryer For Air Compressor
The refrigeration dryer is composed of drying chamber,vacuum system,heat source,and low temperature condenser.In stric accordance with iso9001,gb150,iso7183 refrigerant air dryer standard,qs,pressure vessel inspection specifications for design and manufacture of production and testing,to ensure product safety and reliable operation.
HUADA TPK-20A 2.6 m³/min Fixed-frequency Refrigerated Air Dryer
The HUADA TPK-20A is a fixed-frequency refrigerated compressed air dryer with a nominal treatment capacity of 2.6 m³/min. It combines air-to-air heat recovery, refrigerated moisture condensation and automatic condensate drainage in an orange and dark gray cabinet. Supply: 220 V / 50 Hz; air connection: G1.
HUADA TPK-30A 3.8 m³/min Fixed-frequency Refrigerated Air Dryer
The HUADA TPK-30A is a fixed-frequency refrigerated compressed air dryer with a nominal treatment capacity of 3.8 m³/min. It combines air-to-air heat recovery, refrigerated moisture condensation and automatic condensate drainage in an orange and dark gray cabinet. Supply: 220 V / 50 Hz; air connection: G1 1/2.
YILUMA SV-30 22 kW Single-Stage PM VSD Screw Air Compressor
YILUMA SV-30 is a 22 kW single-stage permanent magnet variable-speed screw air compressor for industrial air supply. It delivers 3.4 m³/min at 0.8 MPa and 2.95 m³/min at 1.0 MPa. The air-cooled package measures 1200 × 900 × 1220 mm, weighs 310 kg and uses a G1 air outlet.
HUADA LGGPM-380 280 kW Air-Cooled Two-Stage Permanent Magnet VSD Screw Air Compressor
The HUADA LGGPM-380 is a 280 kW New A Series two-stage permanent magnet VSD screw air compressor with an air delivery of 60.0 m³/min at 0.8 MPa. A DN125 outlet, large air-cooled enclosure and variable-speed axial fans support planning for high-demand plant air stations.
SC-50 37 kW Permanent Magnet VSD Screw Air Compressor
The SC-50 is a single-stage permanent magnet VSD screw air compressor with a 37 kW motor, for factory systems requiring more airflow than the SC-30. Air delivery is 6.50 m³/min at 7 bar, 6.40 m³/min at 8 bar and 5.40 m³/min at 10 bar. Variable-speed control responds to changing demand, while direct drive and intelligent protection support operation. Its 1300 × 1038 × 1320 mm cabinet and G1 1/4 outlet help buyers plan equipment space and piping.
HuaDa HB-100 Medium-Pressure Permanent Magnet Variable Frequency Screw Air Compressor (75 kW – Specialized for Laser Cutting)
The HB-100 is the flagship medium-pressure permanent-magnet variable-frequency screw compressor from the Huda HB series, delivering a 75 kW power output, an exceptionally high discharge capacity of 9.3 m³/min, and a stable pressure of 1.6 MPa – providing a robust air supply for ultra-large laser cutting centers and continuous heavy-duty production lines.
HUADA LGGPM-100 75 kW Air-Cooled Two-Stage Permanent Magnet VSD Screw Air Compressor
The HUADA LGGPM-100 is a 75 kW New A Series two-stage permanent magnet VSD screw air compressor with an air delivery of 16.5 m³/min at 0.8 MPa. A DN65 outlet and variable-speed centrifugal cooling support integration into a medium-capacity plant air station.
IPv6 network supported
English
français
Deutsch
русский
español
português
日本語
한국의
ไทย
中文
